12 inch Geode Agate Tray Silicone Mold
$61.00
13 in stock
12 inch Geode Agate Tray Silicone Mold
This listing is for one handmade Geode Agate Tray Silicone Mold that you can use for Epoxy Resin casting.**
A finished piece from this mold will measure 11.5 inches wide.
We’ve included a video above, for a more detailed view, that shows the Mold and a finished Resin Tray that we created with Ice Blue Crushed Glass (Finished piece is NOT included.)
This Geode Agate Tray Mold is comprised of what we call “river” and “island” areas (the river runs thru, and around, the island areas.) This Mold has a total of 18 “islands.” On a finished Tray, the top of the river and island areas will be glossy, while the outside round edge of the Tray will be semi-glossy.
To use this mold, you start by filling the river area with your choice of Glitter, Crystals, Mica Powders, or Resin Inks, and then finish pouring the bottom. Once the resin has cured/dried, and you have demolded, you then fill the island inset areas with Crystals, Glass, Flowers, or anything else of your choice, and secure that filler with resin, glue, or varnish. If your end goal is a Clock or piece of Art, to hang on your wall, you can stop there, but if you want to add feet or Lazy Susan hardware, to be able to use the finished Tray on a table, you will have to topcoat the entire piece.
NOTE: The finished resin pieces are shown as samples of what can be created using this mold, and they are not included.
We have uploaded several Video Tutorials, showing how to use this 12 inch Geode Agate Tray Silicone Mold, on our YouTube Channel. Check out the links below to watch them.
Mold Features:
• Made from Platinum Cure Food Grade Silicone
• Glossy surface on top of finished piece
• Round Edge
• This Mold uses approximately 15-17 ounces of resin to pour the river areas and the back/bottom. Any fill in the island areas or a top coat, will require additional resin.
Color: Translucent White
Approximate Measurements: 12” W x .85” H (Finished pieces are approx. 11.5” W x .44” H)
IMPORTANT NOTES:
• This mold is handmade to order. Please allow 5 business days for production.
• Because this is a handmade mold, it might have small imperfections.
• Click the tab above to read our Silicone Mold Care Guide.
** While Silicone Molds can sometimes be used with other casting materials, we have only used these with high quality Epoxy Resin.
Crystal Size Comparison Chart
Dust/Sand: Not measurable
Triple Zero (000): Under 1 mm
Double Zero (00): 1 to 3 mm
Zero (0): 3 to 5 mm
S1: 4 to 6 mm
L1: 5 to 7 mm
Size 2: 6 to 10 mm
Extra Small: 8 to 15 mm
Small: 12 to 20 mm
Medium: 18 to 25 mm
Large: 20 to 30 mm
XL: 30 to 50 mm
NOTE: Color, size, and shape will vary due to the fact that these are natural stones. Also, colors may vary, depending on your monitor settings, and may differ from the actual color of the item.
• Never use a torch or open flame with Silicone Molds.
• Never use anything sharp or abrasive, inside the mold.
• Always use high quality Epoxy Resin products and follow the mixing and pouring directions for that product.
• Keep your mold clean - Keep dust away by storing it in a plastic bag, and only use tape or warm water to clean it.
• The glossy surface of molds will fade away with repeated use. When this happens you will have to topcoat your finished piece, or purchase a new mold.
